![]() |
#301
|
|||
|
|||
![]() Quote:
Bishopscourt May 5th looks good.
__________________
Ronan siR [New addition] Sold! siR [RIP] |
#302
|
|||
|
|||
![]()
My aim is for June Ronan.. Ards Festival of Speed should be well ready by then and on full drag slicks just for the hell of it
__________________
Paul 91 Torino Red EF8 90 Torino Red EF6 |
#303
|
|||
|
|||
![]()
You heading up on Mat 5th anyway? I was thinking of heading up for the gander.
__________________
Ronan siR [New addition] Sold! siR [RIP] |
#304
|
|||
|
|||
![]()
Doubt it Ronan..
June is the big unveil ha ha
__________________
Paul 91 Torino Red EF8 90 Torino Red EF6 |
#305
|
|||
|
|||
![]() Quote:
__________________
Steve -92 EF6 dual carb... neglected out the back -90 EF8 siR... the money pit! |
#306
|
|||
|
|||
![]()
Well finally made it to the dyno with mixed results..
Went up last friday to TTM in Tullamore where I met Trevor (whos mapping the car for me on the obd1 chrome ECU) Here it was the day before getting some final checks ![]() Met at 10am and after getting the base map cleaned up a bit went out on the M8 for some road mapping.. Once we had a smooth drive setup we went on the dyno after lunch for fine tuning.. ![]() The car did feel better but once it came on vtec there seemed to be a hesitation this we though could have been ironed out but its here results came back a little odd.. Basically after many runs on the NON Vtec cam lobe we achieved 150whp @7200rpm witch is very impressive to say the least... Now that seems like a long time before vtec but we could not make power below this so it was necessary. Then after tuning the most Trevor could get was 159whp @7850rpm.. So basically the car was doing nothing on vtec this was due to a few factors mainly my exhaust wasnt up to the task, intake was far to restrictive and insane intake temps taking hot air from the back of the rad.. So we removed the airbox and RSR back box and done two power runs with just a rise in fuel we instantly saw a massive difference.. 178whp!! Thats almost 20whp by just doing that!! SO the plan now is a 2.5" RMF 4-1 replica race header (one of the best manifolds out there with proven gains on dyno shoot outs), custom stainless 2.5" straight exhaust (zerofighter style) for drag racing and a Blox Velocity stack and filter with custom piping heat proofing, cold air feed and box Will up date as I get bits so far I picked up the Blox stack and filter: ![]() ![]() Heres a random run aswell wasnt even on vtec here I think but ye get the idea: http://s10.photobucket.com/albums/a1...t=MVI_2680.mp4 Notice the quiet exhaust!!
__________________
Paul 91 Torino Red EF8 90 Torino Red EF6 |
#307
|
|||
|
|||
![]()
Nice!
__________________
Mark \'91 Black SiR <- Back on the road!! \'92 Red 1.5x (sold) |
#308
|
|||
|
|||
![]()
Fook, that's a sweet sweet figure. That's approx 209BHP (178WHP) from a 1.6 NA Engine. I'd be VERY proud of that figure. Well done Paul.
__________________
Ronan siR [New addition] Sold! siR [RIP] |
#309
|
|||
|
|||
![]()
Did you talk to mr. Lor?
__________________
Steve -92 EF6 dual carb... neglected out the back -90 EF8 siR... the money pit! |
#310
|
|||
|
|||
![]()
Yea thats only an outline figure for now hope to get it to close on 200whp Ronan and thrn a little spray on thet ha ha
Yea Steve not for sale.. Ebay for me now!
__________________
Paul 91 Torino Red EF8 90 Torino Red EF6 |
![]() |
Thread Tools | |
Display Modes | |
|
|