#41
|
|||
|
|||
CRX meet, August/September?
No pressure #128513;
__________________
Paul 91 Torino Red EF8 90 Torino Red EF6 |
#42
|
|||
|
|||
Quote:
__________________
EF7 Torino Red...new project EE8 Cel Blue...gone EF6 Rio Red...RIP EE8 Cel Blue...RIP |
#43
|
|||
|
|||
Quote:
|
#44
|
|||
|
|||
If the meet is at my house I can guarantee there will be 7 CR-Xs there#128513;
We'll probably aim around Dublin to suit north, south and the dubs.
__________________
Paul 91 Torino Red EF8 90 Torino Red EF6 |
#45
|
|||
|
|||
Quote:
__________________
EF7 Torino Red...new project EE8 Cel Blue...gone EF6 Rio Red...RIP EE8 Cel Blue...RIP |
#46
|
|||
|
|||
Its now all in place & I'm slowly but surely getting all the bits bolted back on. Still need a few small things sorted but all in all its 90% where i want it to be for now. A wee bit of paint also makes a serious difference [8D]
__________________
EF7 Torino Red...new project EE8 Cel Blue...gone EF6 Rio Red...RIP EE8 Cel Blue...RIP |
#47
|
|||
|
|||
So, had an issue with the d/side shaft binding with the subframe. I had set the engine & gearbox up trying to rotate it as much forward as possible so I had extra room at the bulk head/firewall. It was all held in position based on the modifications to the rear T bracket.
So i disconnected the T bracket completely, rotated the engine & box back & it freed up the space I need for the shaft, i still have enough space at the firewall but it's obviously a bit tighter & have "persuaded" the firewall in a spot where the TPS sensor now sits to accommodate this! Before: [/url]2021-07-14_08-44-15 After: [/url]IMG_20210729_212528 Still some minor adjustments to make to the T bracket, then i can bolt it up & hopefully I can fill with fluids ready for a 1st start & the inevitable fault finding!
__________________
EF7 Torino Red...new project EE8 Cel Blue...gone EF6 Rio Red...RIP EE8 Cel Blue...RIP |
#48
|
|||
|
|||
Got my baffle from BYC designs & got it welded into place. Hoping this will prevent as much oil starvation as possible as the h2b kit tends to rotate the engine forward a bit more than normal.
Really good piece of kit & not paper thin, perfect fitment for the sump (he also does H22a options as they are a different shape to the H22a7). Welded into place & now back on the block. [/url]IMG_20210726_221205 [/url]2021-08-02_09-15-03 Link: https://bycdesigns.co.uk/index.php?r...=53&search=h22
__________________
EF7 Torino Red...new project EE8 Cel Blue...gone EF6 Rio Red...RIP EE8 Cel Blue...RIP |
#49
|
|||
|
|||
Sounds like you've broken the back on it at this stage - hopefully the fault finding required is minimal!
|
#50
|
|||
|
|||
I'd have love to have that be it but it wasn't...had to pull it all out again last week, flywheel was wobbling when I tried to crank it, had to reset the clutch, pressure plate & the gearbox. I also think my starter is bucked!
__________________
EF7 Torino Red...new project EE8 Cel Blue...gone EF6 Rio Red...RIP EE8 Cel Blue...RIP |
|
|