#1
|
|||
|
|||
eibach pro springs
I finally got my Eibach springs on the car yesterday and they are fantastic. Car is still stupidly low at the front, but it's nowhere near as crashy as it was. Speedbumps are no longer a problem and the wheels seem very well planted on the road (not bad considering the camber problems)
Can't wait to try them out in the dry Did anyone get a camber kit in the end? I'm thinking it might be on the cards after christmas.
__________________
Mark \'91 Black SiR <- Back on the road!! \'92 Red 1.5x (sold) |
#2
|
|||
|
|||
Going to be paying for mine next week, meant to do it this week but didnt get time.
__________________
89 Black JDM CR-X Si (You might call it a project) 91 Gunmetal Grey UKDM CR-X 16v 98 Passion Orange UKDM Civic VTi MB6 90 White USDM CRX HF (JDM B20B Swap) 05 White USDM Subaru Legacy Outback |
#3
|
|||
|
|||
What kind of money are you looking at? Any links?
__________________
Mark \'91 Black SiR <- Back on the road!! \'92 Red 1.5x (sold) |
#4
|
|||
|
|||
They are makkis ones off CRX UK
220stg delivered but they will be 250 shortly I think Also thats exchanging your old ones afaik. Its very hard to get proper front camber kits for efs. I dont like the ingells one at all and it supposed to be the best out there. I have also a Full-Race traction bar on the way so I will be able to adjust the castor too if needs be. The rears are easy to sort without a kit but may get one eventually.
__________________
89 Black JDM CR-X Si (You might call it a project) 91 Gunmetal Grey UKDM CR-X 16v 98 Passion Orange UKDM Civic VTi MB6 90 White USDM CRX HF (JDM B20B Swap) 05 White USDM Subaru Legacy Outback |
#5
|
|||
|
|||
yeah, I hear a coupe of washers will sort out the rear. 220 sterling is a lot though.
any idea if these would fit? http://store.racerwheel.org/s63-516050680.html
__________________
Mark \'91 Black SiR <- Back on the road!! \'92 Red 1.5x (sold) |
#6
|
|||
|
|||
__________________
Mark \'91 Black SiR <- Back on the road!! \'92 Red 1.5x (sold) |
#7
|
|||
|
|||
The first one you psoted wont fit as the efs ball joint is offset.
The second one I think is just the two ball joints, not the whole arm, they are like the ingalls ones.Give Rob an email at NLM he may be able to help ya a bit more, tell him John from Ireland sent ya Makkis are actually very well designed imo.
__________________
89 Black JDM CR-X Si (You might call it a project) 91 Gunmetal Grey UKDM CR-X 16v 98 Passion Orange UKDM Civic VTi MB6 90 White USDM CRX HF (JDM B20B Swap) 05 White USDM Subaru Legacy Outback |
#8
|
|||
|
|||
I'm not saying thy aren't well designed, it's just that I could find better ways of spending the money.
I've been thinking about getting a set of height adjustible konis for the front and raising the ride height a notch instead.
__________________
Mark \'91 Black SiR <- Back on the road!! \'92 Red 1.5x (sold) |
#9
|
|||
|
|||
Ah I know that mark, I was meaning they are the best design I have seen over the rest.
Ive heard some stories of the balljoint Ingalls type slipping etc. Well worth the money for what youd save on tyres
__________________
89 Black JDM CR-X Si (You might call it a project) 91 Gunmetal Grey UKDM CR-X 16v 98 Passion Orange UKDM Civic VTi MB6 90 White USDM CRX HF (JDM B20B Swap) 05 White USDM Subaru Legacy Outback |
#10
|
|||
|
|||
Yep Id like a set of these but Ill start by spending money on the engine now and the rest will follow hopefully[8D]
__________________
Paul 91 Torino Red EF8 90 Torino Red EF6 |
|
|