|
|
#1
11-23-2010, 10:42 AM
|
|||
|
|||
Camber adjusters
Hi lads just wondering do any of ye have camber adjusters on the front of your cars?? My front top wishbone balljoints are worn and ive to replace the whole arms. The car is lowered so this has thrown off the camber. I think the car has around 45-50mm of a drop, not too sure really. I got tyres recently and the fitter recommended getting them as the passenger tyre was worn uneven. But i reckon if all new bushings and ball joints go back in it will tighten up the suspension again and it can be tracked properly. Its impossible to track a car with play in the suspension from worn bushings...
Do they help much? Is the car lowered enough to justify them? If the chamber in the car is in does it take corners better? Anyonr recommend a brand and place to get them?? 
|
|
#2
11-25-2010, 10:24 AM
|
|||
|
|||
|
skunk 2. i think they are about 250 a side. i would deffently get all the bushings done first tho because that will make a massive difference. i think price on wishbone is 67 euro. i have a set of SPC lower adjustable ball joints if your interested
__________________
1991 Ef6 1.5x (R.I.P) 1990 Ef7 si project
|
|
#3
11-25-2010, 09:03 PM
|
|||
|
|||
|
See alot of Buddy Club and K Sport front adjusters being used recently they are all pretty much the same design just a personal preference really (although out of the two above the Buddy Club would have a better name)
I have a set of custom ones that were done as a group buy on CRXuk years ago way defferent design but alot better no chance of slip and really well made (got em off John (cyclonium) about 4years ago
__________________
Paul 91 Torino Red EF8 90 Torino Red EF6
|
|
#4
11-25-2010, 11:04 PM
|
|||
|
|||
|
Have any pics of them crex?
|
|
#6
11-26-2010, 07:15 PM
|
|||
|
|||
|
Thay are fitted to the CRX man Ill have a look to see if there is pics on CRXuk somewhere though
__________________
Paul 91 Torino Red EF8 90 Torino Red EF6
|
|
#7
11-19-2011, 05:38 AM
|
|||
|
|||
|
How are these going for you Paul? Any slippage or anything? Gonna have to get/engineer a set for myself sometime and was wondering what the design was like, it looked good to me though.
__________________
89 Black JDM CR-X Si (You might call it a project) 91 Gunmetal Grey UKDM CR-X 16v 98 Passion Orange UKDM Civic VTi MB6 90 White USDM CRX HF (JDM B20B Swap) 05 White USDM Subaru Legacy Outback
|
|
#8
11-21-2011, 06:33 AM
|
|||
|
|||
|
These cant slip cause theay are bolted up and are adjusted by adding or taking away plates great design but they were expensive enough even with that group buy
__________________
Paul 91 Torino Red EF8 90 Torino Red EF6
|
|
#9
11-21-2011, 10:50 PM
|
|||
|
|||
|
Yeah was wondering was there any wear at all on the plates?
I should have copied/sketched them up before I sent them off with you so I could make some up. Will have to do it the hard way now. This reminds me, I still have to pick up my roll centre adjusters off Nick in CDA!! I assume they are still going strong?
__________________
89 Black JDM CR-X Si (You might call it a project) 91 Gunmetal Grey UKDM CR-X 16v 98 Passion Orange UKDM Civic VTi MB6 90 White USDM CRX HF (JDM B20B Swap) 05 White USDM Subaru Legacy Outback
|
|
#10
11-21-2011, 11:09 PM
|
|||
|
|||
|
ha Ha Ha What!!
Dont think there is too much left in CDA they are getting a bad old rap on the sites lately!
__________________
Paul 91 Torino Red EF8 90 Torino Red EF6
|
 |
|
|
Linear Mode
